# Cutover runbook — USG to VyOS **Print this.** During the cutover there is no internet, so there is no assistant and no web search. Everything you need is on this page and on the boxes themselves. ## Use these addresses. Not the other ones. | | use this | do NOT use | |---|---|---| | vyos001 (MASTER) | **`10.0.1.252`** | ~~192.168.8.143~~ | | vyos002 (BACKUP) | **`10.0.1.253`** | ~~192.168.8.144~~ | `ssh vyos@10.0.1.252` — by IP, not by name. **The `192.168.8.x` addresses stop working the instant the USG is unplugged.** That is not a maybe. Your workstation is on LoT (`10.0.0.210/23`) and reaching `192.168.8.x` requires routing *through the USG*: ``` ip route get 192.168.8.143 -> via 10.0.0.1 <- the USG. Gone. ip route get 10.0.1.252 -> dev lanbr0 <- same L2. Survives. ``` `10.0.1.252` and `.253` are on the LoT VLAN, the same broadcast domain as your workstation, so they need no gateway at all. They are the only remote path that survives the cutover. **Between unplugging the USG and finishing the switch there is no inter-VLAN routing.** In that window: - the **JetKVMs are unreachable** from your workstation (they are on Management and kvm) — they are *not* a fallback during the gap - **Tailscale is down** with the internet - your workstation keeps `10.0.0.210` (86400s lease) and can still resolve via `10.0.0.194`, which is also link-scope If LoT SSH fails, the next step is physical console, not the network. | | | |---|---| | JetKVMs (after routing is restored) | `192.168.1.28`, `192.168.1.29`, `192.168.3.6` | | Switch script | `/config/vyos-unifi-switch` on each box | | Peer link | `eth3` ↔ `eth3` direct cable, 2.5 GbE, `10.255.255.0/30` — conntrack state sync | | Login | user `vyos` | --- ## If something is wrong, do this ``` sudo /config/vyos-unifi-switch unifi ``` Then reconnect the USG. That command runs no health checks, asks nothing and cannot refuse. It restores a byte-exact copy of the configuration the box had before the cutover — verified by diff, not by assumption. **You do not have to be quick.** If you do nothing at all after `vyos-unifi-switch vyos`, the box reverts by itself within 10 minutes. Verified: config returns to the previous state and the box does **not** reboot (`uptime` and boot-id unchanged across an auto-revert). --- ## What has actually been tested Proven on the labsim router (same VyOS version, isolated OVS bridge with no physical NIC), by loading **vyos001's real running config** and applying the **real production delta**: - All 317 commands accepted, and the whole delta **commits** (`COMMIT OK`). - `unifi` mode restores the previous config **byte-exact** (diff clean). - Auto-revert fires when the commit is not confirmed: config returns to the saved state and the box does **not** reboot — `uptime` and boot-id unchanged across the revert. - Failed health checks trigger an immediate revert rather than waiting out the timer. Two bugs were found this way and would each have failed the entire switch, since the delta commits as one unit: `bond0.51` did not exist for PPPoE to reference, and `translation port` rejects a port list. **Not tested, and untestable in advance:** - **PPPoE.** The line permits one session and the USG holds it. The first real attempt is during the cutover. - **The commit on the real boxes.** The rehearsal ran with vyos001's `eth2` and `eth3` stanzas stripped, because the sim VM has only two NICs. Those are plain interface configs that already work on the real hardware, but they were not part of what committed. ## Before you unplug anything 1. Tether your workstation to your phone if you want the assistant available. Cutting the USG cuts your internet, not your LAN. 2. On **both** boxes, confirm the machinery is present: ``` sudo /config/vyos-unifi-switch status ls -la /config/modes/ # unifi.boot + to-vyos.commands ls -la /config/wan-secrets # must be 0600 ``` `status` must report `mode: unifi`. If `unifi.boot` is missing, **stop** — there is no way back without it. 3. Confirm the revert action is `reload`, not `reboot`: ``` show configuration commands | match commit-confirm ``` Must show `action 'reload'`. Without it a failed switch **reboots** the firewall instead of reverting it. The switch script refuses to run if this is missing, but check anyway. ## The cutover 0. **Open both SSH sessions BEFORE you unplug anything**, and leave them open: ``` ssh vyos@10.0.1.253 # vyos002, BACKUP ssh vyos@10.0.1.252 # vyos001, MASTER ``` If either will not connect, stop. Do not unplug the USG. 1. **Physically disconnect the USG.** Not just powered off — disconnected. The switch script refuses to run while anything still answers on a gateway address, because two devices on `.1` is the worst available outcome. You cannot switch first and unplug after, for exactly that reason. 2. In the **vyos002 (BACKUP)** session, first: ``` sudo /config/vyos-unifi-switch vyos ``` 3. Watch the health checks. They cover PPPoE, the default route, kea, the DNS forwarder and reachability. On failure the script reverts immediately and tells you so. 4. If vyos002 came up clean, repeat on **vyos001 (MASTER)**. 5. Check a real client: does it get an address, and is it the *same* address as before? Every active client has a reservation, so it should be. ## What will probably go wrong first **The WAN.** There are two, and they behave differently: | | line | VLAN | transport | notes | |---|---|---|---|---| | WAN2 | 10 gig ISP | **53** | DHCP, public `87.192.101.48/21` | primary, distance 1 | | WAN1 | Vodafone | **51** | PPPoE, ~900/700 Mbit | failover, distance 10 | VyOS clones the USG's WAN2 MAC (`f0:9f:c2:12:9b:4f`) on `bond0.53`, which is how it keeps the existing public lease rather than asking for a new one. **Both boxes carry the identical WAN and NAT config.** vyos002's WAN interfaces are simply held administratively down, so the cloned MAC is never live on two boxes at once. To move the internet path to vyos002: ``` configure delete interfaces bonding bond0 vif 53 disable delete interfaces pppoe pppoe0 disable commit; save ``` Two lines. Do it only when vyos001 is genuinely down or disconnected — two boxes holding that MAC at once is exactly what the disable prevents. PPPoE is no longer an unknown: it was proven on the USG before cutover (`pppoe0` came up with `90.241.226.213`, MTU 1492). What remains untested is VyOS dialling it, and whether the ISP hands the same lease to the cloned MAC. If the WAN check fails: ``` show interfaces pppoe pppoe0 sudo journalctl -u ppp@pppoe0 -n 50 --no-pager ``` Check the credential in `/config/wan-secrets` and that VLAN 51 actually reaches the box. If it will not come up, run `vyos-unifi-switch unifi`, reconnect the USG, and debug with the internet back on. ## Things that are true and easy to forget - **WiFi keeps working, but through VyOS.** The SSIDs stay in UniFi and the APs are untouched, but 37 of 83 active clients are wireless and every one is on LoT — they get their addresses from VyOS now. - **DHCP leases last 24h (86400s).** A device that does not renew promptly keeps its old address for a while. That is fine, not a symptom. - **The firewalls resolve via `8.8.8.8` / `8.8.4.4`** — matching the DNS the USG used on its WAN. This means their own name resolution now depends on the *internet* being up, so between unplugging the USG and PPPoE establishing, the boxes have no DNS at all. That is expected and harmless: they only need DNS for NTP hostnames, and the switch's own health checks use it precisely to prove the WAN came up. Nothing in the switch itself resolves a name. - Internal `ad.itaz.eu` names still resolve through Google, because that zone is published publicly with private addresses in it (`nas001` → `10.0.0.194`, `kvm-macstudio1` → `192.168.3.8`). Convenient here; worth knowing it is public. - **The USG was a DNS resolver** for every VLAN except LoT. VyOS now runs `dns forwarding` in its place. If names stop resolving but IPs still work, that is where to look. - **`eth2` and `bond0.2` are both in `192.168.8.0/23`.** It works, but if you see odd source-address behaviour on the management NIC, that is why. ## Afterwards Once it has been stable for a day: - Re-run `migration/unifi-export.py` — the UniFi controller is no longer the source of truth for DHCP, and the export will drift. - The VPN rules (ESP, UDP 500/4500) are carried over but the VPN itself still terminated on the USG. Decide whether it moves. - `labsim` still holds a deliberate `kvm→k8s` drop rule from earlier testing.