lab/labsim/sim-net-apply.sh

#!/usr/bin/env bash
# Apply -- or drift-check -- the labsim routing config on all four VMs.
#
#   ./sim-net-apply.sh check    what the VMs run vs what sim-net-config.py says
#   ./sim-net-apply.sh apply    push the generated config over the serial console
#
# `check` is the one you want most of the time. The whole failure mode this
# guards against is somebody (including me) fixing something on a VM over SSH
# and never writing it down, so the next rebuild silently loses it.
#
# Applied over the serial console rather than SSH because a freshly installed
# sim router holds the same addresses as its peer -- there is a window where it
# is not safely reachable over the network at all. See console-apply.py.
set -uo pipefail
HERE="$(cd "$(dirname "${BASH_SOURCE[0]}")" && pwd)"
ACTION="${1:-check}"
WORK="$(mktemp -d)"; trap 'rm -rf "$WORK"' EXIT

# role : vm : address : regex selecting the subtrees this generator owns
TARGETS=(
  "primary:labsim-vyos:172.31.1.252:^set (protocols (bgp|failover|static)|policy (prefix-list|route-map)|nat source rule 1[12]0|interfaces (pppoe|bonding bond0 vif 5[13])|firewall (group interface-group LAN|ipv4|ipv6))"
  "secondary:labsim-vyos2:172.31.1.253:^set (protocols bgp|policy (prefix-list|route-map)|firewall (group interface-group LAN|ipv4|ipv6))"
  "isp-dhcp:labsim-isp-dhcp:192.168.122.136:^set (interfaces ethernet|nat source|service dhcp-server|firewall ipv4 forward|system host-name)"
  "isp-pppoe:labsim-isp-pppoe:192.168.122.63:^set (interfaces ethernet|nat source|service pppoe-server|firewall ipv4 forward|system host-name)"
)
# Sim-only credential; these VMs hold nothing real and are not reachable from
# outside the hypervisor.
SSH_OPTS=(-o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null
          -o LogLevel=ERROR -o PreferredAuthentications=password -o ConnectTimeout=5)
live() { timeout 30 sshpass -p vyos ssh "${SSH_OPTS[@]}" "vyos@$1" \
           "/opt/vyatta/bin/vyatta-op-cmd-wrapper show configuration commands" 2>/dev/null; }
norm() { sed "s/'//g" | grep -v 'hw-id\|offload' | sort -u; }

rc=0
for t in "${TARGETS[@]}"; do
  IFS=: read -r role vm addr rx <<<"$t"
  "$HERE/sim-net-config.py" --role "$role" >"$WORK/$role.conf" 2>/dev/null || {
    printf '  %-11s GENERATE FAILED\n' "$role"; rc=1; continue; }

  if [ "$ACTION" = apply ]; then
    printf '  %-11s applying to %s over console...\n' "$role" "$vm"
    "$HERE/console-apply.py" --vm "$vm" --config "$WORK/$role.conf" || rc=1
    continue
  fi

  if ! live "$addr" >"$WORK/$role.live" || [ ! -s "$WORK/$role.live" ]; then
    printf '  %-11s UNREACHABLE (%s)\n' "$role" "$addr"; rc=1; continue
  fi
  grep -E '^set ' "$WORK/$role.conf" | norm >"$WORK/$role.g"
  grep -E "$rx" "$WORK/$role.live" | norm >"$WORK/$role.l"
  if d="$(diff "$WORK/$role.g" "$WORK/$role.l")" && [ -z "$d" ]; then
    printf '  %-11s in sync (%s commands)\n' "$role" "$(wc -l <"$WORK/$role.g")"
  else
    printf '  %-11s DRIFT — "<" only in code, ">" only on the VM:\n' "$role"
    printf '%s\n' "$d" | sed 's/^/      /'
    rc=1
  fi
done
exit $rc